|
OGF -
Mechanically Tuned, Full Band Gunn Oscillators
|
OGF Series Gunn oscillators are near full waveguide band mechanically
tuned Gunn oscillators. The oscillators combine proprietary circuit design capability
and experience with either GaAs or InP Gunn diode to cover the frequency range of
18 to 110 GHz in seven waveguide bands. The oscillators are especially designed
for high output power, full waveguide band mechanical tuning range, bias tuning
ability and low AM/FM noise characteristics. The standard oscillators are equipped
with a micrometer
driver, which enables convenient frequency tuning and reliable frequency resetting.
Unlike many other
competitorsÆ products, these oscillators are equipped with a single mechanical
tuner, which eases frequency and power control. The oscillator can be converted
to an electrical/mechanical-tuned oscillator by replacing micrometer with an electrical
driven motor.
|
|
|
OGI -
Injection Locked Gunn Diode Oscillators
|
OGI series CW injection-locked Gunn oscillators are alternatives
to HEMT device and IMPATT diode based stable amplifiers, especially at high millimeterwave
frequencies. The operating frequency and power output of these oscillators are up
to 110 GHz and 24 dBm. The spectrum purity of the output signal is injected signal
dependent. There is an output free running signal in the absence of an input
injection signal. The oscillators are provided with integral circulators and optional
DC voltage regulator. An optional heater is provided to achieve better temperature
stability. For higher gain, broader locking bandwidth and higher output, multi-stage
and multi-diodes configurations are used.
|
|
|
OGL -
Low Cost K and Ka Band Gunn Diode Oscillators
|
OGL Series K and Ka band Gunn diode oscillators are especially
designed for low cost commercial applications. Unlike most manufacturersÆ
products, these oscillators are made of high performance devices and machined aluminum
cavities. Due to extremely high external Q and temperature compensation mechanism,
these oscillators exhibit higher frequency and power stability, lower phasenoise
and higher anti-load-pulling abilities. The oscillators are ideal candidates for
the applications suchas Police Speed Radar Gunn and Doppler Sensors, where low close-in
phase noise is required.
|
|
|
OGM -
Mechanically Tuned Gunn Diode Oscillators
|
OGM Series mechanically tuned Gunn oscillators combine proprietary
circuit design capability and experience with either GaAs or InP Gunn diode to cover
the frequency range of 18 to 110 GHz in seven waveguide bands. The oscillators are
especially designed for high output power, wide mechanical tuning range, bias tuning
ability and low AM/FM noise characteristics. The standard oscillators are equipped
with a micrometer driver, which enables convenient frequency tuning and reliable
frequency resetting. The oscillators are ideally suited for bench test sources,
while a self-locking screw can be provided
instead of micrometer driver for system integration. The oscillators can be supplied
with optional integrated isolator, voltage regulator and temperature heater. While
waveguide is standard interface, the oscillators are available with coaxial interface
as an option.
|
|
|
OGR -
Gunn Oscillator Bias Regulator
|
OGR and OMR series Gunn oscillator bias regulator and regulator/modulator
are developed as a low noise DC regulator/ modulator for Gunn diode oscillators.
The OGR regulator and OMR regulator/modulator supplies well regulated, low noise
DC voltage to Gunn oscillators. This feature enhances Gunn oscillator signal purity
and also provides protection against destructive over-voltage to the Gunn diode.
The OMR regulator/modulator features internal or external AM or FM modulation capabilities.
The internal modulation rate is 1 KHz and external modulation rate is from DC and
up to 1 MHz. This feature allows phase locking the Gunn oscillator to a microwave
source-locking counter via bias voltage.
|
|
|
OMR -
Gunn Oscillator Bias Regulator & Modulator
|
OGR and OMR series Gunn oscillator bias regulator and regulator/modulator
are developed as a low noise DC regulator/ modulator for Gunn diode oscillators.
The OGR regulator and OMR regulator/modulator supplies well regulated, low noise
DC voltage to Gunn oscillators. This feature enhances Gunn oscillator signal purity
and also provides protection against destructive over-voltage to the Gunn diode.
The OMR regulator/modulator features internal or external AM or FM modulation capabilities.
The internal modulation rate is 1 KHz and external modulation rate is from DC and
up to 1 MHz. This feature allows phase locking the Gunn oscillator to a microwave
source-locking counter via bias voltage.
|
|
|
OGV -
Varactor Tuned Gunn Diode Oscillators
|
OGV series varactor tuned Gunn oscillators combine proprietary
circuit design capability and experience with either GaAs or InP Gunn diode to cover
the frequency range of 18 to 110 GHz in seven waveguide bands. The oscillators are
especially designed for high output power, wide varactor tuning range, mechanical
tuning ability and low AM/FM noise characteristics. The DC power is applied via
a low pass EMI filter, while a female SMA connector is utilized for the varactor
tuning voltage. The tuning rate can be as high as 50 MHz. The oscillators are ideally
suited for FMCW transceivers, AFC loops and phase locked systems. The oscillators
can be supplied with an optional integrated isolator, voltage regulator and temperature
heater. While waveguide is standard interface, the oscillators are available with
coaxial interface as an option. The operating temperature range is 0 to +50°C.
|
|
|
OGB -
Bias Tuned Gunn Oscillators
|
OGB Series bias tuned Gunn oscillators combine proprietary circuit
design capability and experience with either GaAs or InP Gunn diode to cover the
frequency range of 18 to 140 GHz in 9 waveguide bands. The oscillators are especially
designed for high output power, fast bias tuning ability and low AM/FM noise characteristics.
The standard models are equipped with feedthru pin for bias port, while a SMA (F)
connector can be specified at the time of order for better EM shielding. The oscillators
can be supplied with optional integrated isolator, OMG Gunn oscillator modulator/regulator
and temperature heater. Combined with the OMR Gunn oscillator modulator/regulator,
the bias-tuning characteristic of the oscillator can be enhanced without additional
circuitry. The benefit of utilizing bias tuned Gunn oscillator includes better linearity
and higher power output compared with its counter part, Varactor Tuned Gunn oscillator
(OGV). While waveguide is the standard interface, the oscillators are available
with coaxial interface as an option.
|
|
|
OPL - Phase Locked Oscillators
|
OPL series phase-locked oscillators are offered to cover frequency
range up to 110 GHz by utilizing high performance FET oscillators, Gunn oscillators
or multiplier/amplifier chain to produce desired frequency and power output. The
phase locked oscillators are offered with either internal or external referenced
version. The phase noise of an externally referenced phase locked oscillator is
depended on the quality of the reference signal.
|
|
|
OFD -
Dielectric Resonator Oscillators
|
OFD dielectric resonator stabilized oscillators cover the frequency
range of 5 to 26.5 GHz. The oscillators utilize state of the art MIC and FET devices
technology to provide highly stable, reliable and efficient signal sources. Each
oscillator has an internal voltage regulator to provide regulated bias and over-voltage
protection. Standard units are rated over 0 to +50 C operating temperature
range. Standard products incorporate a screw tuner with a reliable self-locking
feature to provide small mechanical frequency tuning. SMA or K female coaxial connector
is equipped for standard RF interface. The electrical tunable dielectric resonator
oscillators are offered as non-standard units. Consult factory for technical information
regarding this choice.
|
|
|
ONS -
Millimeterwave Solid State Noise Sources
|
The ONS Series of solid state noise sources cover full waveguide
bands. The noise sources offered cover the frequency range of 26.5 to 170 GHz in
eight overlapping waveguide bands. The noise sources utilize a silicon IMPATT diode
to provide a stable 15 dB typical ENR. The bias voltage and current for the noise
source are +28 Vdc at 60 mA typical, which is compatible with the Agilent 8970A/B
noise meters. The standard noise sources are supplied with a full band Faraday isolator.
While waveguide is the standard interface, the noise sources are also available
with a coaxial interface by using the appropriate WiseWave PTC series waveguide
to coax adapter up to 110 GHz.
|
|